shell temperature

Turbine Shell Temperature and Thermal Expension Models of A Powerplant Simulator

电站仿真器的透平金属温度与相对膨胀模型

Review of infrared shell temperature measuring method on rotary kilns

回转窑表面温度红外检测法综述

Firstly, paper analyzes the signification of the aluminum tank shell temperature detection to aluminum technics and the health condition calculation of aluminum reduction cell. Research the status quo of the aluminum reduction cell shell temperature detection.

论文首先分析了铝电解槽壳温度检测对铝电解工艺及铝电解槽健康状况预测的重要意义，调研了铝电解槽槽壳温度检测的研究现状。

Ltd. The calculation indicates that converter heat insulation layer thickness of asbestos board is about 30 mm. The converter shell temperature can be controlled within 360 ℃, which is lower than the creep temperature of shell material.

对重钢50t转炉进行了炉壳（炉身段）温度场分析，计算表明：转炉隔热层石棉板的厚度为30mm时，炉壳温度就能控制在360℃以内，低于炉壳材质的蠕变温度。

When the thickness of asbestos board reaches 30 mm, the shell temperature could be controlled below 360 ℃, which is lower than the creep temperature of the shell material, and the thermal expansion stress of the shell is only 50% of that without asbestos board.

当石棉板厚度为30mm左右时，炉壳温度可以控制在360℃以下；低于炉壳材质的蠕变温度，炉壳所受到的热膨胀应力仅为没加石棉板时的50%。

If a means of sealing the shell tapping is provided, it shall be suitable for the full pressure/ temperature rating of the valve.

如果提供了用于密封筒形丝锥的工具，这个工序必须适用于阀门所有压力/度等级。

The design method of on-line shell temperature measuring system is introduced in this paper. It is emphasized to measure shell temperature with thermal couple and ADAM module here.

介绍了铝电解槽壳温度在线检测系统的设计方法，重点讲述了如何应用热电偶和ADAM模块进行温度采集和传送。

According to numerical simulation and molten steel solidification mechanism, in the paper, the restrict relationship had been setup between casting speed and molten steel level and average mould tapping section thickness as well as its shell temperature at tapping spout.

本文基于数值模拟和钢液凝固机理，建立起结晶器内钢液液位和铸坯拉速对其出钢口处钢液截面平均温度和坯壳温度的制约关系。

A kind of three layered 32-node temperature shell element is presented for the transient temperature field FEM analysis of the honeycomb sandwich composite shell.

提出一种三层32结点温度壳单元，对蜂窝夹芯复合材料壳体的瞬态温度场进行了有限元分析。

Finite element analysis of random vibration responses for multilayer shell structure applied with combined temperature and vibration environment

温振复合载荷作用下多层壳结构随机振动响应有限元分析

Traditional analytical method establish model with shell unit, the method ignore the thermal distortion from temperature gradient.

而传统分析方法是按壳单元建立模型，忽略了温度梯度引起的热变形。

The main cause of deformation of a converter shell is temperature rising of the converter shell, a economical and effective method to reduce the temperature and creep deformation is adopting a heat insulation layer of asbestos board.

转炉炉壳温度升高是炉壳变形的主要原因，采用内衬石棉板隔热是降低中小型转炉炉壳温度、减轻炉壳蠕变变形的经济有效措施之一。

Testing and Analysis of Temperature Field of Camshaft during Solidification Produced by Shell Mold with Iron Shot Backing

壳型填铁丸工艺条件下凸轮轴凝固温度场测试及分析

Research on Thermal Stress Equivalent Static Load for Shell under Effect of Constant Temperature Field

常量定常温度场作用下壳体热应力当量静载的试验研究